The Rolec EVO is a 7.4kW untethered smart EV charger for single-phase home charging, from Rolec, a UK EV charging manufacturer based in Lincolnshire. It has a universal Type 2 socket with a motorised lock, a Daytona Grey PC-ABS body measuring 260 x 260 x 112mm, and a dynamic LED ring that shows charging status. The EVO connects over Wi-Fi 6 or Ethernet, with Bluetooth for set-up, and runs on the Rolec EVO app or any OCPP 1.6J back office. A CT clamp with a 10m lead and two RFID cards come in the box, and built-in PEN fault detection means no earth rod on a PME supply. Specifications Model Rolec EVO 7.4kW (ROLEC5011) Power Output Up to 7.4kW / 32A single phase Charging Current 6A to 32A, adjustable Supply 230V AC, 50/60Hz Connector Untethered Type 2 socket with motorised lock (cable not included) Colour Daytona Grey Display Dynamic LED ring Connectivity Wi-Fi 6 (2.4GHz), Ethernet, Bluetooth 5 LE Access Control App, RFID (2 cards included), plug and charge App Rolec EVO app OCPP 1.6J RCD Protection Built-in Type A 30mA with 6mA DC, with test button PEN Fault Protection Built in (no earth rod needed on PME supplies) Other Protection Internal surge, over and under voltage, overload, short circuit, over temperature Load Balancing Dynamic, using the supplied CT clamp (10m lead) Solar Charging ECO and ECO+ modes; second CT kit optional Energy Metering Built in, over 98% accuracy Weather and Impact Rating IP54, IK10 Dimensions (W x H x D) 260 x 260 x 112mm Weight Under 3kg Operating Temperature -30°C to +50°C Standby Power Under 5W Enclosure PC-ABS, UL94 V-0, aluminium heat sink In the Box Charger, CT clamp with 10m lead, 2 RFID cards, wall anchors and screws, sealing plugs, strain reliefs, M25 to M20 reducer, tools, manual Compliance UKCA, CB and TÜV, BS EN IEC 61851-1, IEC 62955, Smart Charge Point Regulations compliant Warranty 5 years Charging Modes The Rolec EVO app has three modes. Charge Now runs at full power. ECO charges from solar during the day and from the grid on a schedule at night. ECO+ charges from surplus solar only. For solar modes, the supplied CT clamp reads grid import and export, and an optional second CT on the solar side gives more accurate readings. Smart Tariffs and Back-Office Control Schedule charging in the Rolec EVO app to match off-peak hours on tariffs such as Octopus Go, Next Drive or British Gas Electric Driver. Because the EVO supports OCPP 1.6J, landlords and small businesses can also connect it to a third-party back office for access control and billing. Firmware updates arrive over the air. Installation Requirements Rolec recommends a 40A MCB or 30mA Type A RCBO upstream, with 6mm² supply cable (10 to 20mm outer diameter) and a wall at least 70mm thick. Cable enters from the top, bottom or rear, with a separate entry for Ethernet and the CT lead. The EVO mounts on a wall or on a Rolec post with the EVO post plate. A qualified electrician registered with a competent person scheme, such as NICEIC or NAPIT, should install it. If you have no suitable wall, mount the charger on an EV charger post. Common Questions Is there a tethered Rolec EVO?No. The EVO 7.4kW is untethered only, so you use your own Type 2 cable. Does the Rolec EVO need an earth rod?Not on a PME (TN-C-S) supply. Its built-in PEN fault detection disconnects the charger if the PEN conductor fails. What warranty does the Rolec EVO have?5 years as standard from Rolec. Keep your installer's test and inspection record, as Rolec may ask for it with a claim.